Specs:

Lutro PHPM-PA-120-WH | Phase-Adaptive Power Module White

Dimensions and Mounting

• Mount in 2-gang U.S. wallbox, 3.5 in (89 mm) deep or 4 × 4 in (102 × 102 mm) junction box, 2.1 in (53 mm) deep.
  
• For indoor use only.
  
• This device generates heat; mount only where ambient temperature is 32 to 104 °F (0 to 40 °C).
  
• Mount with arrows facing up to ensure adequate cooling.
  
• Allow 4.5 in (114 mm) above and below faceplates when mounting several modules in a vertical layout.
  
• Units may butt together when mounted in a horizontal layout.
  
• Mount so line (mains) voltage wiring is at least 6 ft (1.8 m) from sound or electronic equipment and wiring.
  
• Mount within 7° of true vertical.
  
  Power
  
• Control voltage: 120 V~ only
  
• Load voltage: 120 V~ only
  
• Capacity: Full 16 A 120 V~: 1920 W 120 – 277 V~: 1920 – 4432 W 220 – 240 V~: 3520 – 3840 W
  
• Frequency: 50 / 60 Hz
  
• Load (output) power: Phase independent of control device / control voltage
  
  Sources / Load Types
  
• Operates these sources with a smooth, continuous, Square Law dimming curve: – Incandescent (tungsten)– Halogen– Magnetic low-voltage transformer (iron core)– Electronic (solid-state) low-voltage transformer (must be manufacturer-approved for reverse-phase control dimming)– Neon / Cold cathode
  
• Incandescent and electronic low-voltage sources may be controlled on the same circuit / control zone. Up to 30% of the capacity of the unit can be used for incandescent lighting.
  
• Incandescent and magnetic low-voltage sources may be controlled on the same circuit / control zone. Up to 30% of the capacity of the unit can be used for incandescent lighting.
  
• Electronic low-voltage and magnetic low-voltage sources may NOT be controlled on the same circuit / control zone.
  
• PHPM-PA- and PHPM-WBX- models are not for use with non-dim loads. Use switching power module (PHPM-SW-DV-WH) for non-dim loads.
  
• Minimum load on power module is 10 W.
  
• Output must be directly connected to
  

Features:

• Provides dimming control for 1 zone of a full 16 A lighting load.
  
• May be used to dim incandescent, halogen, electronic low-voltage, magnetic low-voltage, neon / cold cathode.
  
• Phase-adaptive technology automatically selects leadingedge or trailing-edge dimming for low-voltage transformers.
  
• Up to 3 power modules may be controlled by a single dimmer (C5-BMJ- will control only 1 module).
  
• Use PHPM-WBX- models for 3-wire fluorescent dimmer input and PHPM-PA- models for 2-wire input.
  
• PHPM-WBX- models can be used in conjunction with BCI-0-10 for 0 – 10 V dimming applications.
  
• Models available for control voltage of 120 V~ only or 220 – 277 V~.
  
• Models available for load voltage of 120 V~ only or 120 – 277 V~.
  
• Compatible with 220 / 240 V~, non-CE systems. Contact Lutron for specific system applications.
  
• Not for use with non-dim loads.
  
  Works with 120 V~ or 220 – 277 V~ versions of:
  
• Lutron in-wall neutral wire dimmers; see approved list in the Dimmers and Switches Specification Guide (Lutron P/N 3671746) at www.lutron.com (see Lighting Load Interfaces section)
  
• GRAFIK Eye QS control units *
  
• LP, LCP, and GP dimming panels **
  
• HomeWorks QS remote power panels **
  
• HomeWorks QS in-line dimmer
  
• HomeWorks QS DIN-rail power modules
  
• EcoSystem interface C5-BMJ-XXX †
  
• Energi Savr Node PRO LED+ phase-adaptive fixture controller
  
• RadioRA 2 neutral wire dimmers; see approved list in the specification submittal (Lutron P/N 369225) at www.lutron.com
  
• HomeWorks QS neutral wire dimmers; see approved list in the specification submittal (Lutron P/N 369305) at www.lutron.com
  
• Caséta Wireless neutral wire dimmers; see approved list in the specification submittal (Lutron P/N 369987) at www.lutron.com
  
• Vive PowPak phase select dimming modules;
  

Overview:

Provides dimming control for 1 zone of a full 16 A lighting load.

May be used to dim incandescent, halogen, electronic low-voltage, magnetic low-voltage, neon / cold cathode.
Phase-adaptive technology automatically selects leadingedge or trailing-edge dimming for low-voltage transformers.
Up to 3 power modules may be controlled by a single dimmer (C5-BMJ- will control only 1 module).

Review: