1 RJ45 Jack: 100/1000 Ethernet DHCP Enabled by Default
Digital Audio Inputs:
2 Optical TOSLINK Inputs
2 Coaxial RCA Inputs
Stereo, PCM, 96kHz, 24-bit
Line Level Audio Inputs:
4 Stereo / 8 Mono Analog RCA Inputs
Configurable to Left, Right, or Mono
Max input level 2.0 VRMS
Input Sensitivity: 0dbV (1.0 VRMS)
Input Impedance: 47k Ω-49k Ω
Doorbell Audio Input
3.5mm Stereo Input
Maximum input level: 2.0 VRMS
Input sensitivity: 0dbV (1.0 VRMS)
Input impedance 47k Ω to 49k Ω
Line Level Audio Outputs
Stereo / 4 Mono Analog RCA Pre-amp Outputs
Configurable to Left, Right, Mono, or Sub-woofer
Fixed or variable line level output Fixed: 0 dB nominal gain
Variable: -50 to +0dB at 0.5dB per step Unbalanced
Output impedance: 470 Ω
Amplifier Output
4 Stereo / 8 Mono Amplified Outputs
Configurable to Left, Right, or Mono
Output Power: 80W at 8Ω, 100W at 4Ω
THD: < 0.05% @ 1kHz
Frequency Response: 20Hz to 20kHz, +.5dB/-.5dB
Crosstalk: >60dB @ 1kHz/1W
Signal to Noise: >100dB
Lip Sync Delay
Individual Lip Sync Delay for Each Speaker and Preamp Zone
Delay Time: 0 â?? 400ms
Adjustable: 10ms increments
Tone Control
Individual Tone Control for Each Speaker and Preamp Zone
Five-band equalizer
Loudness on/off
High/Low pass
Adjustable Crossover Points
Trigger Outputs
3.5mm Mono
Zone Trigger / System Trigger Outputs
Pinout: Tip = signal, Sleeve = ground
Output: +12Vdc, 100mA current limit
Power
AC 100-120 / 220-240 V~ 50/60Hz, 1000W
Temperature
Operating Temperature: +5° C â?? +45° C (+41°F â?? +113°F)
Operating Humidity: 0 â?? 90% non-condensing
Storage Temperature: 0° C â?? +60° C (32°F â?? +140°F)
Dimensions
17D X 17W X 4H in. / 431.8D X 431.8W X 101.6H mm (with feet)
17D X 17W X 3.5 in. / 431.8D X 431.8W X 88.9H mm (without feet)
Weight: 21.9 lbs / 9.93 Kg
Features:
4 Stereo or 8 Mono Amplified Zones and 2 Stereo or 4 Mono Pre-amp Zones
Expandable with Additional Chassis and Optional Dante Network Audio Card
80WPC at 8Ω, 100WPC at 4Ω
2 Optical, 2 Co-ax, and 4 Stereo / 8 Mono Analog Inputs
DSP with 5-Band EQ for Each Zone
Lip Sync Correction
Overview:
Important Note: EL-IPD-MTX-8CH replaces the S86A. Reach out to your RSM for any questions.
The EL-IPD-8CH-MTX amplifier can be used in stand alone mode to support up to 13 input sources (4 digital, 8 mono / 4 stereo analog RCA and 1 stereo 3.5mm typically used as the doorbell input from an ELAN System Controller). Each RCA analog input can be configured with another as a L/R pair or individually as mono. 8 speaker channels are available (up to 4 stereo zones or 8 mono zones). 4 line level outputs can be configured as up to 4 mono or 2 stereo output zones or as sub-woofer out. Each can be configured as left, right, mono, or sub out.
Adding the optional Dante™ Audio Networking card connects sources to and from other Dante™ enabled ELAN IP amplifiers using existing networks.
ELAN IP enabled audio distribution simplifies whole home audio distribution and enhances the intelligent home by delivering high quality audio over the existing network. Easily scaling from a single chassis solution to a decentralized multi-chassis / multi-source implementation, ELAN IP audio distribution meets the needs for projects of up to 64 individual zones.